BrickLink Discussion Forum

Discussion Forum

Redisplay Messages: Compact | Brief | All | Full Show Messages: All | Without Replies

Re: Inventory Change Request for Set 7735-1 - Admin_Russell

[...] You simply cannot explain everything that happens with Lego. Experienced collectors know this. There is the barrel theory, that Lego just gets to the bottom of the barrel [...]
(75 months ago, Feb 23, 2018, to Inventories Requests)

Re: Inventory Change Request for Set 7735-1 - StormChaser (566)

[...] Seeing all the photos which have recently surfaced of sealed train sets, I find it difficult to understand why it would be difficult to locate some hard proof for any [...]
(75 months ago, Feb 23, 2018, to Inventories Requests)

Re: Inventory Change Request for Set 7735-1 - CrazyChris (223)

[...] I know, but I refuse this kind of reasoning. Because it does not explain, why set A is affected, but not set B. These parts were quite common and exist in not too many [...]
(75 months ago, Feb 23, 2018, to Inventories Requests)

Re: Inventory Change Request for Set 7735-1 - PurpleDave (969)

[...] Introduced =/= exclusive. Old molds can be run alongside new ones for various amounts of time. Old parts can be in inventory for years as they bleed the stock down, [...]
(75 months ago, Feb 23, 2018, to Inventories Requests)

Re: Inventory Change Request for Set 7735-1 - CrazyChris (223)

But SezaR is right. It is common knowledge that the hinges with hollow studs were introduced around 1987. It is also common knowledge that the set 7735 was produced from 1until [...]
(75 months ago, Feb 23, 2018, to Inventories Requests)

Re: Inventory Change Request for Set 7735-1 - legoman77 (3628)

[...] You are not too hard. Getting inventories correct is a very hard job. You might look at Perron. I did a lot of stuff for that catalog. I often would use two or more sets [...]
(75 months ago, Feb 23, 2018, to Inventories Requests)

Re: Inventory Change Request for Set 7735-1 - Admin_Russell

[...] We are not going to approve requests to blanket the inventory system with every possible variant. If you want to add a variant to an inventory, you need to a have a reliable [...]
(75 months ago, Feb 23, 2018, to Inventories Requests)

Inventory Change Request for Set 7735-1 - SezaR (1383)

Please make changes to the following inventory: (Set 7735-1) * Add 2 Part 4276 Black Hinge Plate 1 x 2 with 2 Fingers (match ID 1) * Add 2 Part 4275 Black Hinge Plate [...]
(75 months ago, Feb 23, 2018, to Inventories Requests)

Re: Inventory Change Request for Set 118-1 - StormChaser (566)

[...] Yes, there are a few reasons why these requests have not been approved: 1. The inventory you've recently submitted for the part you want to add includes exactly [...]
(75 months ago, Feb 23, 2018, to Inventories Requests)

Re: Interface improvement - chetzler (2319)

[...] Fair point. I should have said "community interest". I don't fault BrickLink for wanting to make money--that's why most all of us (sellers, at least) [...]
(75 months ago, Feb 23, 2018, to Suggestions)

Re: Interface improvement - TheBrickGuys (13267)

[...] "My interest" is very subjective. The problem is that so many feel the same way as you do so in that when a change or changes are made and it dose not benefit what they [...]
(75 months ago, Feb 23, 2018, to Suggestions)

Re: Interface improvement - leopard37 (4528)

[...]
(75 months ago, Feb 23, 2018, to Suggestions)

Re: Interface improvement - leopard37 (4528)

[...] I think more like this:
(75 months ago, Feb 23, 2018, to Suggestions)

Re: Interface improvement - chetzler (2319)

[...] They wouldn't get that response if they cared to develop even a basic understanding of the BrickLink community (both buying and selling) and the AFOL community [...]
(75 months ago, Feb 23, 2018, to Suggestions)

Re: Interface improvement - qwertyboy (7854)

[...] Sometimes it actually reads like this:
(75 months ago, Feb 23, 2018, to Suggestions)

Re: Interface improvement - WoutR (919)

[...] I must admit that it is a good representation of how I currently feel. I see some good things happening, but there is a lot that worries me.
(75 months ago, Feb 23, 2018, to Suggestions)

Re: Interface improvement - nectara (6580)

[...] Wrong Is more like this
(75 months ago, Feb 23, 2018, to Suggestions)

Re: Interface improvement - TheBrickGuys (13267)

Don't forget the typical forum response to ANYTHING that admin tries to do....
(75 months ago, Feb 23, 2018, to Suggestions)

Re: Interface improvement - nectara (6580)

[...] +1
(75 months ago, Feb 23, 2018, to Suggestions)

Re: Interface improvement - calsbricks (8510)

[...] A little while ago when Jaclyn's predecessor was here I got a lifetime ban from the forum for something similar to this. Fortunately she got the 'move on out [...]
(75 months ago, Feb 23, 2018, to Suggestions)

Re: Interface improvement - legoman77 (3628)

[...] That was funny, my laugh of the day. Keep it up! John P
(75 months ago, Feb 23, 2018, to Suggestions)

Interface improvement - Teup (6596)

In my opinion, icons that accurately represent functionality are a key part in having a good interface. It has come to my attention that the icon of the Community tab is outdated [...]
(75 months ago, Feb 23, 2018, to Suggestions)

Re: Inventory Change Request for Set 7710-1 - SezaR (1383)

We know that since 1983 (or earlier?), the sleeprs 767 were replaced by 4166 with cable grooves as the cable grooves were needed for the set 7866. Ths set 7710 was released [...]
(75 months ago, Feb 23, 2018, to Inventories Requests)

Inventory Change Request for Set 7710-1 - SezaR (1383)

Please make changes to the following inventory: (Set 7710-1) * Add 32 Part 4166 Dark Gray Train, Track Sleeper Plate 2 x 8 with Cable Grooves (match ID 4) * Change 32 [...]
(75 months ago, Feb 23, 2018, to Inventories Requests)

Re: Inventory Change Request for Set 118-1 - wannes. (814)

[...] Is there a reason why this does not get approved?
(75 months ago, Feb 23, 2018, to Inventories Requests)

Next Page: 5 More | 10 More | 25 More | 50 More | 100 More