Discussion Forum: Thread 307363 |
|
|
| | Author: | jagpaw184 | Posted: | Aug 3, 2021 05:23 | Subject: | Inventory Change Request for Set 396-1 | Viewed: | 45 times | Topic: | Inventories | Status: | Open | |
|
| Please make changes to the following inventory:
* Change {9 to 13} Part Black 3005 Brick 1 x 1
* Change {19 to 20} Part Black 3010 Brick 1 x 4
* Change {10 to 9} Part Black 3008 Brick 1 x 8
Comments from Submitter:
Item quantity altered to match plans. Step 3: rear top row is 1x4 and 2 1x1 (1x6 used in step 12). Step 12 top of boiler hatch 1x6 and 2 1x1 (1x8 removed)
|
|
| | | | | |
| | | | Author: | Turez | Posted: | Aug 3, 2021 06:43 | Subject: | Re: Inventory Change Request for Set 396-1 | Viewed: | 26 times | Topic: | Inventories | |
|
| In Announce, jagpaw184 writes:
| Please make changes to the following inventory:
* Change {9 to 13} Part Black 3005 Brick 1 x 1
* Change {19 to 20} Part Black 3010 Brick 1 x 4
* Change {10 to 9} Part Black 3008 Brick 1 x 8
Comments from Submitter:
Item quantity altered to match plans. Step 3: rear top row is 1x4 and 2 1x1 (1x6 used in step 12). Step 12 top of boiler hatch 1x6 and 2 1x1 (1x8 removed)
|
These changes were made in 2008 by Russell (viejos) but were reverted in 2010:
https://www.bricklink.com/catalogInvChangeItem.asp?itemType=S&itemNo=396-1&viewDate=Y&viewStatus=1
Unfortunately the forum postings from that time are not available anymore but
I guess there must have been a good reason to change the quantities back to 9,
19 and 10, respectively. Therefore I'm not inclined to accept your requests
without further information.
Anyone out there who can help with this?
|
|
|
| | | | | | | | | | | | | | |
| | | | | | | | Author: | peregrinator | Posted: | Oct 16, 2021 06:44 | Subject: | Re: Inventory Change Request for Set 396-1 | Viewed: | 23 times | Topic: | Inventories | |
|
| In Inventories, Admin_Russell writes:
| In Inventories, Turez writes:
| In Announce, jagpaw184 writes:
| Please make changes to the following inventory:
* Change {9 to 13} Part Black 3005 Brick 1 x 1
* Change {19 to 20} Part Black 3010 Brick 1 x 4
* Change {10 to 9} Part Black 3008 Brick 1 x 8
Comments from Submitter:
Item quantity altered to match plans. Step 3: rear top row is 1x4 and 2 1x1 (1x6 used in step 12). Step 12 top of boiler hatch 1x6 and 2 1x1 (1x8 removed)
|
These changes were made in 2008 by Russell (viejos) but were reverted in 2010:
https://www.bricklink.com/catalogInvChangeItem.asp?itemType=S&itemNo=396-1&viewDate=Y&viewStatus=1
Unfortunately the forum postings from that time are not available anymore but
I guess there must have been a good reason to change the quantities back to 9,
19 and 10, respectively. Therefore I'm not inclined to accept your requests
without further information.
Anyone out there who can help with this?
|
What would be super useful at this point is a high quality scan of the instructions
or a sealed set (even better). There are two instances where a long beam (1 x
6 or 1 x 8) is actually a shorter brick with a 1 x 1 on each end. It doesn't
make sense unless one thinks that with the limited resources at the time, these
unusual splits where for decoration purposes.
|
It does seem the submitter is correct from the instructions available online,
which are not of very high quality but do appear to show lines at the ends of
the long beams.
|
|
|
|
|
|
|