Discussion Forum: Thread 283330 |
|
|
| | Author: | Jetflap | Posted: | Feb 5, 2021 13:58 | Subject: | Inventory Change Request for Set 7810-1 | Viewed: | 40 times | Topic: | Inventories Requests (Entry) | Status: | Open | |
|
| Please make changes to the following inventory:
* | | 7810-1 (Inv) Push-Along Steam Engine (Locomotive without motor) 91 Parts, 1 Minifigure, 1980 Sets: Train: 4.5V |
* Delete 5 Part 3010 Black Brick 1 x 4
Comments from Submitter:
Inventory states 5 required for alternate model, this is incorrect it should be 4. I believe the confusion comes from step 6 of the alternate build. The incorrect "5th" part is shown on the front of the engine, however this is actually a Black Slope 45 2 x 4, the tip of which can be just see at the front of the model in this and all additional steps. The slope 2 x 4 is there to cover the two Black Round 1 x 1s from step 2.
|
|
| | | | | |
| | | | Author: | SezaR | Posted: | Feb 5, 2021 17:20 | Subject: | Re: Inventory Change Request for Set 7810-1 | Viewed: | 17 times | Topic: | Inventories Requests | |
|
| In Inventories Requests, Jetflap writes:
| Please make changes to the following inventory:
* | | 7810-1 (Inv) Push-Along Steam Engine (Locomotive without motor) 91 Parts, 1 Minifigure, 1980 Sets: Train: 4.5V |
* Delete 5 Part 3010 Black Brick 1 x 4
Comments from Submitter:
Inventory states 5 required for alternate model, this is incorrect it should be 4. I believe the confusion comes from step 6 of the alternate build. The incorrect "5th" part is shown on the back of the engine, however this is actually a Black Slope 45 2 x 4, the tip of which can be just see at the back of the model in this and all additional steps. The slope 2 x 4 is there to cover the two Black Round 1 x 1s from step 4.
|
Hi JetFlap
See
https://www.bricklink.com/message.asp?ID=1250763
You meant to change the quantity from 5 to 4. You requested to remove all the
1x4 bricks which is not what you meant.
I also changed few words in your text above and bolded them. (I guess it is back
not front?)
|
|
|
| | | | | | | | | |
| | | | | | Author: | Jetflap | Posted: | Feb 5, 2021 17:46 | Subject: | Re: Inventory Change Request for Set 7810-1 | Viewed: | 21 times | Topic: | Inventories Requests | |
|
| Thanks Reza, yes that is all correct! I couldn't figure out how to change
the amount, the change request form is not at all user friendly.
In Inventories Requests, SezaR writes:
| In Inventories Requests, Jetflap writes:
| Please make changes to the following inventory:
* | | 7810-1 (Inv) Push-Along Steam Engine (Locomotive without motor) 91 Parts, 1 Minifigure, 1980 Sets: Train: 4.5V |
* Delete 5 Part 3010 Black Brick 1 x 4
Comments from Submitter:
Inventory states 5 required for alternate model, this is incorrect it should be 4. I believe the confusion comes from step 6 of the alternate build. The incorrect "5th" part is shown on the back of the engine, however this is actually a Black Slope 45 2 x 4, the tip of which can be just see at the back of the model in this and all additional steps. The slope 2 x 4 is there to cover the two Black Round 1 x 1s from step 4.
|
Hi JetFlap
See
https://www.bricklink.com/message.asp?ID=1250763
You meant to change the quantity from 5 to 4. You requested to remove all the
1x4 bricks which is not what you meant.
I also changed few words in your text above and bolded them. (I guess it is back
not front?)
|
|
|
|
| | | | | | | | | | | | | |
| | | | | | | | Author: | SezaR | Posted: | Feb 5, 2021 19:05 | Subject: | Re: Inventory Change Request for Set 7810-1 | Viewed: | 27 times | Topic: | Inventories Requests | |
|
| In Inventories Requests, Jetflap writes:
| Thanks Reza, yes that is all correct! I couldn't figure out how to change
the amount, the change request form is not at all user friendly.
In Inventories Requests, SezaR writes:
| In Inventories Requests, Jetflap writes:
| Please make changes to the following inventory:
* | | 7810-1 (Inv) Push-Along Steam Engine (Locomotive without motor) 91 Parts, 1 Minifigure, 1980 Sets: Train: 4.5V |
* Delete 5 Part 3010 Black Brick 1 x 4
Comments from Submitter:
Inventory states 5 required for alternate model, this is incorrect it should be 4. I believe the confusion comes from step 6 of the alternate build. The incorrect "5th" part is shown on the back of the engine, however this is actually a Black Slope 45 2 x 4, the tip of which can be just see at the back of the model in this and all additional steps. The slope 2 x 4 is there to cover the two Black Round 1 x 1s from step 4.
|
Hi JetFlap
See
https://www.bricklink.com/message.asp?ID=1250763
You meant to change the quantity from 5 to 4. You requested to remove all the
1x4 bricks which is not what you meant.
I also changed few words in your text above and bolded them. (I guess it is back
not front?)
|
|
Hey Colin,
We have an agreement as we both have 577 feedback records at this time: 577 positive
feedbacks! See attached.
|
|
|
|
|
|
|
|