| Discussion Forum: Thread 250018 |
|
 |
| | | Author: | normann1974  | | Posted: | Mar 22, 2019 12:10 | | Subject: | Are 8x10 remote controls identical inside? | | Viewed: | 89 times | | Topic: | Catalog | | Status: | Open | |
|
| Hi
I have a 8x10 remote control without buttons that I want to sell in case anyone
can use it as spare parts (e.g. reuse the springs). But because I can't identify
it by the buttons, I need to know: Are the inside of all five variants the same
(e.g. only the print different)?
/Jan
|
|
|
|
| | | | | |
| | | | | Author: | paulvdb | | Posted: | Mar 22, 2019 13:11 | | Subject: | Re: Are 8x10 remote controls identical inside? | | Viewed: | 35 times | | Topic: | Catalog | |
|
| In Catalog, normann1974 writes:
| | Hi
I have a 8x10 remote control without buttons that I want to sell in case anyone
can use it as spare parts (e.g. reuse the springs). But because I can't identify
it by the buttons, I need to know: Are the inside of all five variants the same
(e.g. only the print different)?
/Jan
|
On three of the images you can see them from the side where you plug in the wires.
Those three all look diffeent so that's one way to tell them apart. Unfortunately
the other two are photographed from the opposite side but maybe you can do a
Google search to see if you can find more images.
|
|
|
| | | | | |
| | | | | Author: | FreeStorm | | Posted: | Mar 22, 2019 20:44 | | Subject: | Re: Are 8x10 remote controls identical inside? | | Viewed: | 33 times | | Topic: | Catalog | |
|
| In Catalog, normann1974 writes:
| | Hi
I have a 8x10 remote control without buttons that I want to sell in case anyone
can use it as spare parts (e.g. reuse the springs). But because I can't identify
it by the buttons, I need to know: Are the inside of all five variants the same
(e.g. only the print different)?
|
[ . . . ]
If on the bottom of part you have the same holes as my picture and only one output
cable connexion.
it can be a earlier version of
new version of 4707pb01 do not have the same holes on the bottom
If you have two output connexion:
|
|
|
|
| | | | | |
| | | | | Author: | brickskipper | | Posted: | Mar 23, 2019 09:13 | | Subject: | Re: Are 8x10 remote controls identical inside? | | Viewed: | 30 times | | Topic: | Catalog | |
|
| I would think it is either a
or
Because in the
there should be more "switching" inside. There was one connector for the LED
signal and another for the power switch to bridge the interruption in the
* | | 3242a Train, Track 12V Conducting Rail Straight for 12v Signal with Rail Interruption in the Middle, no Pattern
Parts: Train, Track |
and in the
should also be more stuff as there were outputs for the motors and also a swichted
output for the flashlights (in fact is was a constant output in which you would
plug in a "Flash Light Unit" (x543) to have flashing lights).
In your picture I only see two springs leading to only one reversible output
which is used for the decoupler and switch.
However, I do not know the
so I cannot say anything about this one.
In Catalog, normann1974 writes:
| | Hi
I have a 8x10 remote control without buttons that I want to sell in case anyone
can use it as spare parts (e.g. reuse the springs). But because I can't identify
it by the buttons, I need to know: Are the inside of all five variants the same
(e.g. only the print different)?
/Jan
|
|
|
|
|
|
|
|
Denmark
Netherlands, Overijssel
Switzerland, Vaud
Germany, Schleswig-Holstein