| Discussion Forum: Thread 244146 |
|
 |
| | | Author: | calsbricks  | | Posted: | Nov 8, 2018 11:39 | | Subject: | Try that again | | Viewed: | 224 times | | Topic: | Catalog | | Status: | Open | |
|
| - Not swure thie is correct in the catalogue. In all 3 sets that
it comes in there is an white rubber band which holds the two halves
together. The instructions show the rubber band being used in each case. Should
there be an inventory for the part?
|
|
| | | | | |
| | | | | Author: | Rob_and_Shelagh | | Posted: | Nov 8, 2018 11:43 | | Subject: | Re: Try that again | | Viewed: | 37 times | | Topic: | Catalog | |
|
| In Catalog, calsbricks writes:
| | - Not swure thie is correct in the catalogue. In all 3 sets that
it comes in there is an white rubber band which holds the two halves
together. The instructions show the rubber band being used in each case. Should
there be an inventory for the part?
|
As currently set up in the catalogue 29112pb01 is for 1 piece i.e. half of the
assembly and the band is just another separate part. For an assembly the inventory
would need to be 2 x 29112pb01 plus one band but typically assemblies like this
are not catalogued.
Robert
|
|
| | | | | | | | | |
| | | | | | | Author: | calsbricks | | Posted: | Nov 8, 2018 11:45 | | Subject: | Re: Try that again | | Viewed: | 31 times | | Topic: | Catalog | |
|
| In Catalog, Rob_and_Shelagh writes:
| | In Catalog, calsbricks writes:
| | - Not swure thie is correct in the catalogue. In all 3 sets that
it comes in there is an white rubber band which holds the two halves
together. The instructions show the rubber band being used in each case. Should
there be an inventory for the part?
|
As currently set up in the catalogue 29112pb01 is for 1 piece i.e. half of the
assembly and the band is just another separate part. For an assembly the inventory
would need to be 2 x 29112pb01 plus one band but typically assemblies like this
are not catalogued.
Robert
|
Hi Robert - I thought there was all this talk and discussion about assemblies
a short time ago and that has changed but I will bow to your knowledge and separate
them out.
|
|
|
| | | | | | | | | | | | | |
| | | | | | | | | Author: | Rob_and_Shelagh | | Posted: | Nov 8, 2018 11:47 | | Subject: | Re: Try that again | | Viewed: | 39 times | | Topic: | Catalog | |
|
| In Catalog, calsbricks writes:
| | In Catalog, Rob_and_Shelagh writes:
| | In Catalog, calsbricks writes:
| | - Not swure thie is correct in the catalogue. In all 3 sets that
it comes in there is an white rubber band which holds the two halves
together. The instructions show the rubber band being used in each case. Should
there be an inventory for the part?
|
As currently set up in the catalogue 29112pb01 is for 1 piece i.e. half of the
assembly and the band is just another separate part. For an assembly the inventory
would need to be 2 x 29112pb01 plus one band but typically assemblies like this
are not catalogued.
Robert
|
Hi Robert - I thought there was all this talk and discussion about assemblies
a short time ago and that has changed but I will bow to your knowledge and separate
them out.
|
Not sure about that discussion but thinking about it the picture may confuse
some buyers into thinking they get 2 halves when ordering 1.. so I'm going
to make that clear in our description.
Robert
|
|
|
| | | | | | | | | | |
| | | | | | | Author: | SylvainLS | | Posted: | Nov 8, 2018 11:46 | | Subject: | Re: Try that again | | Viewed: | 31 times | | Topic: | Catalog | |
|
| In Catalog, Rob_and_Shelagh writes:
| | In Catalog, calsbricks writes:
| | - Not swure thie is correct in the catalogue. In all 3 sets that
it comes in there is an white rubber band which holds the two halves
together. The instructions show the rubber band being used in each case. Should
there be an inventory for the part?
|
As currently set up in the catalogue 29112pb01 is for 1 piece i.e. half of the
assembly
|
Maybe add a simple line in the picture to show it’s both sides of the same part
and not two parts.
| | and the band is just another separate part. For an assembly the inventory
would need to be 2 x 29112pb01 plus one band but typically assemblies like this
are not catalogued.
|
It would need a pin too 
|
|
|
| | | | | | | | | |
| | | | | | | Author: | BeauBricks | | Posted: | Nov 8, 2018 12:05 | | Subject: | Re: Try that again | | Viewed: | 37 times | | Topic: | Catalog | |
|
| In Catalog, Rob_and_Shelagh writes:
| | In Catalog, calsbricks writes:
| | - Not swure thie is correct in the catalogue. In all 3 sets that
it comes in there is an white rubber band which holds the two halves
together. The instructions show the rubber band being used in each case. Should
there be an inventory for the part?
|
As currently set up in the catalogue 29112pb01 is for 1 piece i.e. half of the
assembly and the band is just another separate part. For an assembly the inventory
would need to be 2 x 29112pb01 plus one band but typically assemblies like this
are not catalogued.
Robert
|
This one is:
What are the guidelines that the venus flytrap is not an assembly? It is really
confusing.
|
|
|
| | | | | | | | | | | | | |
| | | | | | | | | Author: | StormChaser | | Posted: | Nov 8, 2018 14:54 | | Subject: | Re: Try that again | | Viewed: | 38 times | | Topic: | Catalog | |
|
| In Catalog, BeauBricks writes:
| | What are the guidelines that the venus flytrap is not an assembly? It is really
confusing.
|
At this moment there are little to no guidelines on what should or should not
be added to the catalog as an assembly. The current part entry for the flytrap
is not an assembly because it is an entry for just one shell (you'd need
two shells plus a couple other parts for a complete assembly).
As for whether the catalog would accept an entry for the complete assembly if
someone submitted it with a photo . . . well, there are no rules. Assemblies
are something which need to be addressed in writing, but which haven't yet
been.
|
|
|
|
|
|
United Kingdom, England
USA, California
France, Nouvelle-Aquitaine
Netherlands, Zuid-Holland
