Discussion Forum: Thread 242777 |
|
|
| | Author: | Brixalotl | Posted: | Oct 8, 2018 14:57 | Subject: | Inventory Change Request for Set 76097-1 | Viewed: | 23 times | Topic: | Inventories Requests (Entry) | Status: | Open | |
|
| Please make changes to the following inventory:
* Delete 2 Part 44567 Dark Bluish Gray Hinge Plate 1 x 2 Locking with 1 Finger on Side (undetermined type)
* Add 2 Part 44567a Dark Bluish Gray Hinge Plate 1 x 2 Locking with 1 Finger on Side with Bottom Groove (match ID 1)
* Add 2 Part 44567b Dark Bluish Gray Hinge Plate 1 x 2 Locking with 1 Finger on Side without Bottom Groove (Alternate) (match ID 1)
* Delete 4 Part 44302 Dark Bluish Gray Hinge Plate 1 x 2 Locking with 2 Fingers on End (undetermined type)
* Add 4 Part 44302a Dark Bluish Gray Hinge Plate 1 x 2 Locking with 2 Fingers on End with Bottom Groove (match ID 2)
* Add 4 Part 44302b Dark Bluish Gray Hinge Plate 1 x 2 Locking with 2 Fingers on End without Bottom Groove (Alternate) (match ID 2)
* Add 2 Part 44301b Light Bluish Gray Hinge Plate 1 x 2 Locking with 1 Finger On End without Bottom Groove (Alternate) (match ID 3)
* Change 2 Part Light Bluish Gray 44301 Hinge Plate 1 x 2 Locking with 1 Finger On End (undetermined type) {match ID 0 to 3}
Comments from Submitter:
confirmed variants during part out, thanks
|
|
|
| | | | | |
| | | | Author: | Hygrotus | Posted: | Oct 9, 2018 15:35 | Subject: | Re: Inventory Change Request for Set 76097-1 | Viewed: | 21 times | Topic: | Inventories Requests | |
|
| In Inventories Requests, Brixalotl writes:
| Please make changes to the following inventory:
* Add 2 Part 44301b Light Bluish Gray Hinge Plate 1 x 2 Locking with 1 Finger On End without Bottom Groove (Alternate) (match ID 3)
* Change 2 Part Light Bluish Gray 44301 Hinge Plate 1 x 2 Locking with 1 Finger On End (undetermined type) {match ID 0 to 3}
|
Here you changing match ID from 0 to 3 of undetermine variant and add determine
variant "b" to alternate leaving undetermine in inventory. Did you wanted to
change undetermine in regular to "a" variant like others hinges in this request?
|
|
| | | | | | | | | |
| | | | | | Author: | Brixalotl | Posted: | Oct 10, 2018 11:09 | Subject: | Re: Inventory Change Request for Set 76097-1 | Viewed: | 19 times | Topic: | Inventories Requests | |
|
| In Inventories Requests, Hygrotus writes:
| In Inventories Requests, Brixalotl writes:
| Please make changes to the following inventory:
* Add 2 Part 44301b Light Bluish Gray Hinge Plate 1 x 2 Locking with 1 Finger On End without Bottom Groove (Alternate) (match ID 3)
* Change 2 Part Light Bluish Gray 44301 Hinge Plate 1 x 2 Locking with 1 Finger On End (undetermined type) {match ID 0 to 3}
|
Here you changing match ID from 0 to 3 of undetermine variant and add determine
variant "b" to alternate leaving undetermine in inventory. Did you wanted to
change undetermine in regular to "a" variant like others hinges in this request?
|
Yes, that works for me. I just didn't want to change the and add the variant
"a" when I hadn't actually found any in that form yet.
Thanks,
Jim
|
|
|
| | | | | | | | | | | | | |
| | | | | | | | Author: | Hygrotus | Posted: | Oct 10, 2018 12:07 | Subject: | Re: Inventory Change Request for Set 76097-1 | Viewed: | 21 times | Topic: | Inventories Requests | |
|
| In Inventories Requests, Brixalotl writes:
| Yes, that works for me. I just didn't want to change the and add the variant
"a" when I hadn't actually found any in that form yet.
Thanks,
Jim
|
Thanks for additional info. So if you hadn't found "a" you only should change
this undetermine one in the regular section, not adding it as alternate leaving
undetermine in the inventory. These hinges were split to two variants quite recently
and undetermine one don't correspond to any current "a" or "b" (variant
were not recognized) like for example was with part 3794 for example were current
3794 was treted before as "a" variant before "a" wasn't added to the catatlog.
I will correct this and "b" one will be added to regular section then.
Marek
|
|
|
|
|
|
|