Discussion Forum: Thread 219109 |
|
|
| | Author: | viejos | Posted: | Apr 10, 2017 22:29 | Subject: | Inventory Change Request for Set 21303-1 | Viewed: | 22 times | Topic: | Inventories Requests (Entry) | Status: | Open | |
|
| Please make changes to the following inventory:
* Change 1 Part Black 3023 Plate 1 x 2 {match ID 1 to 0}
Comments from Submitter:
Please see following post.
|
|
| | | | | |
| | | | Author: | viejos | Posted: | Apr 10, 2017 22:43 | Subject: | Re: Inventory Change Request for Set 21303-1 | Viewed: | 25 times | Topic: | Inventories Requests | |
|
| In Inventories Requests, viejos writes:
| Please make changes to the following inventory:
* Change 1 Part Black 3023 Plate 1 x 2 {match ID 1 to 0}
Comments from Submitter:
Please see following post.
|
If the DBG plates are handled as recommended in my previous post on this inventory,
the removal of the Match ID from the black 1 x 2 plate line should solve the
problem entirely.
After studying what went wrong here:
https://www.bricklink.com/message.asp?ID=1035201
I knew there had to be another mistake, because I had lined up the piece counts
for the two versions and they matched:
https://www.bricklink.com/message.asp?ID=1033493
So, the root of the problem - a Black plate 1 x 2 was removed instead of a DBG
plate. Easy mistake to make with the colors as printed in the instructions. But
all four versions of instructions show the plate in Black being added on p. 75
(or p. 79 for the 3-language version). It is the same color as the lever, and
that only comes in black in this set.
Below is a revised version of the spreadsheet with the corrected lines in red:
|
|
|
|
| | | | | | | | | |
| | | | | | Author: | SylvainLS | Posted: | Apr 11, 2017 06:06 | Subject: | Re: Inventory Change Request for Set 21303-1 | Viewed: | 25 times | Topic: | Inventories Requests | |
|
| In Inventories Requests, viejos writes:
| In Inventories Requests, viejos writes:
| Please make changes to the following inventory:
* Change 1 Part Black 3023 Plate 1 x 2 {match ID 1 to 0}
Comments from Submitter:
Please see following post.
|
If the DBG plates are handled as recommended in my previous post on this inventory,
the removal of the Match ID from the black 1 x 2 plate line should solve the
problem entirely.
After studying what went wrong here:
https://www.bricklink.com/message.asp?ID=1035201
I knew there had to be another mistake, because I had lined up the piece counts
for the two versions and they matched:
https://www.bricklink.com/message.asp?ID=1033493
So, the root of the problem - a Black plate 1 x 2 was removed instead of a DBG
plate. Easy mistake to make with the colors as printed in the instructions. But
all four versions of instructions show the plate in Black being added on p. 75
(or p. 79 for the 3-language version). It is the same color as the lever, and
that only comes in black in this set.
Below is a revised version of the spreadsheet with the corrected lines in red:
|
Please all, accept my apologies.
I’ve no idea why I asked that black plate to be marked as not present in the
new version: clearly, “my” cockroach is all black, and the black plate is in
the parts listing in the instructions.
|
|
|
|
|
|
|