| Redisplay Messages: Compact | Brief | All | Full Show Messages: All | Without Replies |
Author: | paulvdb | Posted: | Sep 19, 2019 03:54 | Subject: | Inventory Change Request for Set 10223-1 | Viewed: | 23 times | Topic: | Inventories Requests (Entry) | Status: | Open | |
|
| Please make changes to the following inventory:
* Change 2 Part Red {2453 Brick 1 x 1 x 5 - Undetermined Stud Type to 2453a Brick 1 x 1 x 5 - Blocked Open Stud or Hollow Stud}
Comments from Submitter:
From set in my personal collection.
|
|
Author: | paulvdb | Posted: | Sep 19, 2019 03:54 | Subject: | Re: Inventory Change Request for Set 10223-1 | Viewed: | 14 times | Topic: | Inventories Requests | |
|
| In Inventories Requests, Turez writes:
| Unfortunatly I didn't find any photos showing 2453a in red.
|
I remember that 2453b was approved to the catalog shortly after I inventoried
this set. Sets that I parted out and one for my personal collection had a mix
of both types in all colors. The one that I still have in my personal collection
has red 2453a. I'll submit a change request for it.
|
|
Author: | SezaR | Posted: | Sep 18, 2019 23:24 | Subject: | Re: Inventory Change Request for Set 112-2 | Viewed: | 24 times | Topic: | Inventories Requests | |
|
| In Inventories Requests, randyf writes:
| In Inventories Requests, SezaR writes:
| In Inventories Requests, SezaR writes:
| Please make changes to the following inventory:
* Add 1 Part bb0007c01pb02 Blue Electric, Motor 4.5V Type A 12 x 4 x 4 with Glued Black Plate 2 x 4 with Holes for Cable Connectors with 4.5 VOLT stamped on front (Alternate) (match ID 3)
* Add 1 Part 3230a Blue Train, Track Tapered Rail Curved Inside
* Add 1 Part 3229a Blue Train, Track Tapered Rail Curved Outside
* Add 1 Part 3228a Blue Train, Track Tapered Rail Straight 16L
* Delete 4 Part wheel1b Red Train Wheel with 2 x 2 Stud Center, Beveled Tread and Cam Axle for Motor
* Add 4 Part wheel1bc01 Red Train Wheel with 2 x 2 Stud Center, Beveled Tread and Cam Axle for Motor with Light Gray Train Rim for 4.5V & 12V Locomotive Wheels (wheel1b / trainrim)
* Delete 4 Part trainrim Light Gray Train Rim for 4.5V & 12V Locomotive Wheels
* Add 3 Part 3034 White Plate 2 x 8
* Change 1 Part Blue bb0007 Electric, Motor 4.5V Type A 12 x 4 x 4 {match ID 0 to 3}
|
See attached photos of a new later release given to me from a collector.
Randy,
I cannot add wires. I don't see why no decision on the project of wire is
not yet taken, after about 6 months. All it is needed to accept that
|
I am on the inventories side and not the catalog side. It is up to Marek and
the new Catalog Associate Paul to take up catalog projects. Marek has been alone
since the beginning of the year and approving new items to the catalog and approving
changes to the catalog takes all of his time. Once Paul gets ramped up, the catalog
side will be able to do more. So if you want the project started, you will need
to lobby them at this time. When I become a Catalog Associate around the end
of October or early Novemeber, I would be happy to start a dialog then if something
has not been started.
Cheers,
Randy
| - the length of wires are not exact (and cannot be defined to be exact in the
title); - the length of wire/connector assembly shall be defined in terms of
the length of wire, like "wire/connector assembly....with wire of length approximately
90cm";
Cheers,
Reza
|
|
Thanks for explaining this.
Few months ago, I think you commented that you had ideas for this project, so
that's why I thought you could also make decisions.
|
|
Author: | randyf | Posted: | Sep 18, 2019 21:42 | Subject: | Re: Inventory Change Request for Set 112-2 | Viewed: | 27 times | Topic: | Inventories Requests | |
|
| In Inventories Requests, SezaR writes:
| In Inventories Requests, SezaR writes:
| Please make changes to the following inventory:
* Add 1 Part bb0007c01pb02 Blue Electric, Motor 4.5V Type A 12 x 4 x 4 with Glued Black Plate 2 x 4 with Holes for Cable Connectors with 4.5 VOLT stamped on front (Alternate) (match ID 3)
* Add 1 Part 3230a Blue Train, Track Tapered Rail Curved Inside
* Add 1 Part 3229a Blue Train, Track Tapered Rail Curved Outside
* Add 1 Part 3228a Blue Train, Track Tapered Rail Straight 16L
* Delete 4 Part wheel1b Red Train Wheel with 2 x 2 Stud Center, Beveled Tread and Cam Axle for Motor
* Add 4 Part wheel1bc01 Red Train Wheel with 2 x 2 Stud Center, Beveled Tread and Cam Axle for Motor with Light Gray Train Rim for 4.5V & 12V Locomotive Wheels (wheel1b / trainrim)
* Delete 4 Part trainrim Light Gray Train Rim for 4.5V & 12V Locomotive Wheels
* Add 3 Part 3034 White Plate 2 x 8
* Change 1 Part Blue bb0007 Electric, Motor 4.5V Type A 12 x 4 x 4 {match ID 0 to 3}
|
See attached photos of a new later release given to me from a collector.
Randy,
I cannot add wires. I don't see why no decision on the project of wire is
not yet taken, after about 6 months. All it is needed to accept that
|
I am on the inventories side and not the catalog side. It is up to Marek and
the new Catalog Associate Paul to take up catalog projects. Marek has been alone
since the beginning of the year and approving new items to the catalog and approving
changes to the catalog takes all of his time. Once Paul gets ramped up, the catalog
side will be able to do more. So if you want the project started, you will need
to lobby them at this time. When I become a Catalog Associate around the end
of October or early Novemeber, I would be happy to start a dialog then if something
has not been started.
Cheers,
Randy
| - the length of wires are not exact (and cannot be defined to be exact in the
title); - the length of wire/connector assembly shall be defined in terms of
the length of wire, like "wire/connector assembly....with wire of length approximately
90cm";
Cheers,
Reza
|
|
|
Next Page: 5 More | 10 More | 25 More | 50 More | 100 More
|
|