| Redisplay Messages: Compact | Brief | All | Full Show Messages: All | Without Replies Author: | calsbricks | Posted: | Nov 21, 2018 09:39 | Subject: | Inventory Change Request for Set 40222-1 | Viewed: | 197 times | Topic: | Inventories Requests (Entry) | Status: | Open | |
|
| Please make changes to the following inventory:
* Add 1 Part 44567b Light Bluish Gray Hinge Plate 1 x 2 Locking with 1 Finger on Side without Bottom Groove (Alternate)
* Add 1 Part 44302b Dark Bluish Gray Hinge Plate 1 x 2 Locking with 2 Fingers on End without Bottom Groove (Alternate)
Comments from Submitter:
5 sets parted out all without groove.
|
|
Author: | calsbricks | Posted: | Nov 21, 2018 08:43 | Subject: | Re: Projectile Launcher | Viewed: | 182 times | Topic: | Catalog | |
|
| In Catalog, StormChaser writes:
| In Catalog, calsbricks writes:
| Change for the sake of change is often followed by complaints - it rarely serves
any real purpose. Agreed changes often come with compliments and welcoming. There
is a difference.
|
That's a reasonable assessment. However, I'm fairly confident that the
changes I've made or coordinated in the catalog so far were all improvements.
Still, I've gotten a number of complaints about nearly all of them.
|
How does that go - you can please some of the people all of the time but not
all of the people all of the time
NB - We haven't had reason yet to complain other than taking up the entire
forum with catalogue and inventory change requests ....
|
|
Author: | calsbricks | Posted: | Nov 21, 2018 07:56 | Subject: | Re: Projectile Launcher | Viewed: | 352 times | Topic: | Catalog | |
|
| In Catalog, StormChaser writes:
| In Catalog, Teup writes:
That was the point of the Projectile Launcher category: to group all of these
together in one place. However, I'd prefer to wait for the launch of the
parts reclassification project to move these.
The first part of that project will be creating precise written definitions for
every category of parts. Once written definitions exist, then people will have
less room to bring out the torches and pitchforks when parts start moving.
Don't know if you noticed or not, but people sometimes want change and then
complain when it happens.
|
Change for the sake of change is often followed by complaints - it rarely serves
any real purpose. Agreed changes often come with compliments and welcoming. There
is a difference.
|
|
Author: | calsbricks | Posted: | Nov 8, 2018 11:45 | Subject: | Re: Try that again | Viewed: | 31 times | Topic: | Catalog | |
|
| In Catalog, Rob_and_Shelagh writes:
| In Catalog, calsbricks writes:
| - Not swure thie is correct in the catalogue. In all 3 sets that
it comes in there is an white rubber band which holds the two halves
together. The instructions show the rubber band being used in each case. Should
there be an inventory for the part?
|
As currently set up in the catalogue 29112pb01 is for 1 piece i.e. half of the
assembly and the band is just another separate part. For an assembly the inventory
would need to be 2 x 29112pb01 plus one band but typically assemblies like this
are not catalogued.
Robert
|
Hi Robert - I thought there was all this talk and discussion about assemblies
a short time ago and that has changed but I will bow to your knowledge and separate
them out.
|
|
Author: | calsbricks | Posted: | Nov 8, 2018 11:39 | Subject: | Try that again | Viewed: | 224 times | Topic: | Catalog | Status: | Open | |
|
| - Not swure thie is correct in the catalogue. In all 3 sets that
it comes in there is an white rubber band which holds the two halves
together. The instructions show the rubber band being used in each case. Should
there be an inventory for the part?
|
Next Page: 5 More | 10 More | 25 More | 50 More | 100 More
|
|